2015/05/05

AL-NET-8

About AL-Net-8
iControl Electronics Co., Ltd
www.icontrol.com.vn
•  Artnet, 8 Universal DMX System. 
•  Standard DMX-512 8 Universal DMX System. 

•  High Speed DMX-1000K(1M) 2048 dmx channels per universe 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
About AL-Net-8 
Introduction: 
Thank you for your purchasing the Acclaim Lighting 8 Universal DMX System(AL-NET-8). To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the  basic operation of this system. The Acclaim Lighting AL-NET-8 is simple to use, 8 Universal  DMX System. All system components & software have been tested at the factory before being shipped to you. These software include X-mapping & X-Software. Before use this system, please backup them in  your computer, then simply connect the LAN-cable(RJ45) between  your AL-NET-8 and  your computer, then you're ready to go! 

The AL-NET-8 has been thoroughly tested and shippedin perfect working condition. Please take a few minutes to carefully inspect the system carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect each system component for damage, in the case that damage is found, please contact our customer support center, listed below, for further instructions. 
Every  effort  has  been made  to  design  dependable  and reliable  products.  New  products  are  constantly being designed to meet the needs of the entertainment lighting industry. Your comments regarding our products and services are welcome. Acclaim Lightingwill provide set up help and to answer any question should you encounter problems during you set up or initial operation. You may also visit us on the webat for any comments or suggestions. And please send usan e-mail to and let us know how to improve to better serve you. It is both a privilege and a pleasure serving you. 
There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your  manufactures  warranty.  In  the  unlikely  event  your  unit  may  require  service,  please  contact  your nearest  Acclaim  Lighting  dealer.  Do  not  discard  this  carton  in  the  trash,  please  recycle  when  ever possible.  Upon  unpacking,  carefully  inspect  your  unit  for  any  damage  that  any  have  occurred  during shipping. If damage may have occurred, do not plug  the unit in, please contact your dealer as soon as possible. 




Setup hardware 
Notes 
This is a step by step guide to ensure a successfulstartup of our X-Software & AL-Net 8 package with Windows XP. If you plan on using Windows Vista, please contact us first as you may encounter some issues . If any further questions arise, please feel free to contact us for technical support. 
Step 1: Hardware Configuration 
Make sure your PC’s Ethernet Port is connected to the Port on the AL-Net, that all power supplies are on and  not  exceeding  the  recommended  load,  and  that  all  data  cables  (3  Pin  DMX)  are  run  to  the corresponding PD- 150’s. There are 2 dip switches on the front of the AL-Net 8. 
When using Acclaim X-Software, make sure that switch 1 is on (CL100 mode) and switch 2 is off. 
Also make a note of the IP address on the back of the AL-Net 8. The default address is 172.16.0.250. If you are using multiple AL-Net 8’s make sure that the IP address’ are only one number apart. (i.e. Node1 = 172.16.0.250, Node 2 = 172.16.0.251). 
Please be aware that IP addresses 172.16.0.0, 172.16.0.3, 172.16.0.255 are not available for use.
Controls & Functions: Front Panel View 
ArtNet encoder: To activate and set SubNet and Universe of ArtNet. Anduse Universe encode to set the starting number of the existing node's Universe. 
Power Indicator: To indicate the work status of the unit. 
Ethernet port: With RJ 45 standard network port. 
Link/Data Indicator: To indicate the status of network linking and data linking. 
Link/Data Indicator: To indicate the status of network linking and signal/data linking. 
250K/1000K indicator:  To indicate the signal output of 8 Universe DMX uses standard DMX-512 protocol or 
Work Mode Selector(SW1~2): To select and activate the Control Protocol as you desire; 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Special Note: 

1.  Under CL100M protocol, the AL-Net-8 Configuration software from Acclaim Lighting will be available. You MUST firstly set your PC's IP address of "172.16.0.3", and Sub mask addressing of "255.255.255.0". 
2.  Once you remove Sw1 or Sw2 if you need, you MUST restart your AL-Net-8. (How to set your PC's IP addressing and Subnet mask addressing, please referto "Configuring Ethernet card".) 
IP Address Setting(SW1~3 Operation): 
Before using the node, please set the existing AL-Net-8's IP addressing from 1720.16.0.[0]~172.16.0.[255] by using SW1~SW3 as you desired. As per AL-Net-8, 172.16.0.0, 172.16.0.3, 172.16.0.255 are not available. 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
NOTE: 
In case of the value of IP address when you set the IP address of AL-Net-8 exceeds 255, the "172.16.0.250" will be available as the IP address of the existing node automatically. 
Step 2: Program Installation 
Unzip the X-Software Setup file. Once unzipped openthe X-Software setup folder and double click on the setup icon. Install X-Soft to the default location  in Program Files. You should receive a confirmationthat the install was successfully completed. 
After installation you should have these 4 programs. 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Step 3: Set IP Address 
You must set your computers LAN connection to a specific IP Address in order to properly communicate with the DMX Node you are using. 
To do this go to: 
Start Menu -> Control Panel -> Network 
Connections.  Right  click  on  Local  Area  Connection  and  select  Properties.  In  the  Properties  window, select Internet Protocol (TCP/IP) and click on Properties. Select Use the following IP address. 
If you are using the AL-Net 8 Node you will enter 171.16.0.3 in the IP address section and 255.255.255.0 in the Subnet Mask section. Click OK to confirm. 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Step 4: set IP address in Set Form:
Start XSoftwaresetting proramm. 
Click on “Show Form”on top of window. 
Click on “Show IPSetForm” 
For  these  connected  Nodes  controlling  the  fixtures  correctly,  all  nodes  which  are  used  to  control  the Fixtures MUST be set up individual IP address in this Setup software. 
Enter  a  valid  integer  value  of  node  (AL-Net  8’s)  quantity  which  will  be  used  as  needed  in  the  entire systemin the top left box marked  IP.Then under IP Address, enter the IP Address from the back of your AL-Net 8.
172.16.0.0, 172.16.0.3 and 172.16.0.255 are not available. 
Click the Test Hardware checkbox and click Save Set. 
All settings will be saved automatically.
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Step 4 : X-Mapping Software 
How to Create a Pixel Map 
start X-mapping software on desktop. 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Set the needed screen dimensions, 
Set the needed node numbers 
Once you set this numbers it isn’t possible to change. You have to start over again. 
After all devices and fixtures settings are finished, access to built a pixel map as needed.
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn


ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
6.1. Select an existing device which you wish to create a pixel map. 
6.2. Select an existing node which you to use to control device. 
6.3. Select an existing output port of selected node to control device. 
6.4. Click the grey area in Work Grid till Arrow( )turn red, Grid( )turn green in Toolbar. 
6.5. Then click the Grid( ) to array device's pixels and create the pixel map.
Device Select is a drop down menu that displays existing device which you wish to assign the device to the Pixel Map.. Select an existing device which youwish to create a pixel map. 

To remove the device from map double click right mouse button. 
ArtNet Controller
iController Electronics Co., Ltd
www.icontrol.com.vn


Then click the pixel map assign devices pixels direction according to the scan order which has been set up. 
Double click left mouse button to set device number. Device number will automatic increase when double click on next device . 
Select Output is a drop down menu that displays existing output port of selected node which you wish to use to control your devices actually. 
To edit device number and/or node or port number press right button 
ArtNet Controller
iControl Electronics Co., Ltd
www.icontrol.com.vn
Node Address is a drop down menu that displays existing nodes which you wish to use to control your devices actually. 



After you're satisfied with overall settings, you can click the ''Convert Map Address'' icon to convert the pixel map addresses and upload to Node. (Node should be connected to pc) 
Pixel mapping is now competed and ready for use.

0 comments:

Post a Comment

 

ArtNet Controller DMX © 2015 - Designed by Templateism.com, Plugins By MyBloggerLab.com